Rod and Reel Accessories

Abu Garcia Precision Grease is formulated specifically for high-performance fishing reel components — a low viscosity grease engineered to lubricate gears, bearings, and moving parts in baitcast reels without the drag and resistance of heavier general-purpose greases. Heat and cold resistant for consistent performance across a wide range of fishing conditions, with corrosion protection that extends component life in both freshwater and saltwater environments. 1 oz.

Key Features

• Low Viscosity Formula — Lower viscosity than general-purpose greases allows the lubricant to flow into tight tolerances between gears, bearings, and moving parts without creating drag or resistance; critical for high-performance baitcast reels where excess lubricant viscosity reduces casting distance and retrieve smoothness.
• High-Performance Parts — Formulated for the precision tolerances of high-performance reel components — main gears, pinion gears, level wind mechanisms, and bearing races; provides the lubrication film needed to protect metal-on-metal contact points under the sustained load of fighting large fish.
• Heat & Cold Resistant — Maintains consistent viscosity and lubrication performance across a wide temperature range; does not thin out and run in hot summer conditions or thicken and stiffen in cold water winter fishing — critical for year-round reel performance without seasonal re-lubrication.
• Corrosion Protection — Corrosion-inhibiting formula protects metal reel components from rust and oxidation in both freshwater and saltwater environments; extends the service life of gears, bearings, and moving parts exposed to water, humidity, and salt spray.
• Baitcast Reel Optimized — Specifically recommended for baitcast reels where gear and bearing lubrication directly affects casting performance and retrieve smoothness; compatible with Abu Garcia baitcast reels and other high-performance baitcasters requiring precision lubrication.

Best For

• Baitcast Reel Maintenance — Primary application for baitcast reel gear and bearing lubrication during routine maintenance; apply to main gear, pinion gear, level wind worm gear, and bearing races for smooth, quiet operation and maximum casting performance.
• Saltwater Reel Protection — Corrosion-inhibiting formula provides essential protection for reel components exposed to saltwater, salt spray, and high-humidity coastal environments; apply after saltwater use to displace moisture and protect metal components from corrosion.
• Year-Round Use — Heat and cold resistance makes the Precision Grease effective across all seasons without changing lubricants; consistent viscosity from cold water winter fishing through hot summer conditions eliminates the need for seasonal lubrication changes.
• Abu Garcia Reel Service — The manufacturer’s recommended grease for Abu Garcia baitcast reel service; using the correct viscosity and formulation maintains warranty compliance and ensures optimal performance from Abu Garcia reel components.

When you're locked in a fight with tuna, yellowtail, or any hard-charging offshore target, a shifting reel isn't just annoying — it kills your leverage and risks losing the fish. The Accurate Ascender Reel Clamp Kit is the OEM solution engineered specifically for Ascender series reels, delivering rock-solid rod seat mounting under extreme drag pressure.

When the Fight Gets Real

High-torque cranking puts massive stress on the reel-to-rod connection. Standard reel seats can loosen over time, especially on heavy drag setups. This kit locks your Ascender down hard — no movement, no creep, no compromise. It's what serious offshore anglers reach for before heading to the grounds.

What's In the Box

• Heavy-duty reel clamp (black corrosion-resistant finish)
• Mounting studs
• Securing nuts
• All hardware needed for a complete installation

Built for Ascender Reels — Nothing Else

This is an Accurate-specific kit. It is not a universal clamp. Compatible reels must have stud holes — narrow versions of the Ascender series do not have stud holes and are not compatible. Verify your exact model before ordering.

The Right Pick If...

• You're running an Accurate Ascender 300, 400, or 500 series reel
• You're fishing offshore for tuna, yellowtail, or large pelagics
• You want OEM hardware — not a generic clamp that may not seat correctly
• Your current reel seat shows any sign of loosening under load

Key Features

• Accurate OEM fit — engineered specifically for Ascender series reels
• Complete hardware kit — studs, nuts, and clamp all included
• Black corrosion-resistant finish — built for saltwater environments
• Maximum stability — eliminates reel movement during high-torque cranking
• Available in two sizes — Small (300/400) and Large (400/500)

Best Fishing Techniques

• Slow pitch jigging
• Speed jigging
• Live bait offshore
• Chunking and deep drop

Best Conditions

• Offshore bluewater fishing
• High-drag, heavy-tackle setups
• Saltwater environments requiring corrosion-resistant hardware

Best For

• Bluefin, yellowfin, and bigeye tuna
• Yellowtail and amberjack
• Large pelagics requiring sustained drag pressure
• Any Accurate Ascender 300/400/500 owner wanting secure, OEM-grade mounting

Tackle Express Tips

• Apply a small amount of anti-seize compound to the mounting studs before installation — it makes removal much easier after extended salt exposure.
• Confirm your Ascender model number before selecting size. The 400 size can go either way depending on the specific reel — check the reel body for stud hole placement.
• Inspect the clamp and studs annually if fishing in heavy saltwater conditions, especially on live bait or chunking trips where the reel sees continuous load.

FAQ

Will this fit a narrow version of the Accurate Ascender?
No. Narrow Ascender models do not have stud holes and are not compatible with this clamp kit. Only standard (non-narrow) Ascender reels can use this hardware.

Do I need any special tools to install this kit?
No special tools required. Standard hand tools are sufficient for installation. All mounting hardware is included in the kit.

Which size should I order for an Ascender 400?
The Ascender 400 is compatible with both Small and Large versions of this kit depending on the specific variant. Check your reel's stud hole configuration or contact us and we can help confirm the right fit.

Cinching a knot tight with bare hands is one of the fastest ways to cut yourself on the water. The Accurate Knot Puller solves that problem cleanly — it lets you seat your knot with full, even pressure and zero risk of the line slicing into your fingers. Whether you're building a leader topside or re-rigging mid-trip, this is the kind of small tool you notice immediately when you don't have it.

The Line-Cutting Problem

Fluorocarbon and heavy braid don't give. When you pull a knot tight by hand on 50–80 lb line, you're either not cinching it fully — leaving a weaker knot — or you're cutting into your hands. Over a long trip with multiple re-rigs, that adds up. The Accurate Knot Puller gives you a rubber-coated grip surface that the line bites into, letting you apply full pulling force without contact with the line itself.

How It Works

The knot puller is two pieces that screw together for a compact profile that fits in a tackle tray or pocket. It includes a hole at the top for a keyring or lanyard attachment, and a slot that accepts a hook directly — useful for cinching connection knots at the hook end. Both pieces have a black rubber coating that gives the line something to grip during the pull.

The Right Pick If...

• You tie knots with heavier fluorocarbon or braid where bare-hand cinching risks injury
• You re-rig frequently on the water and want a compact, pocketable tool for the job
• You want a clean way to seat Bimini twists, FG knots, uni-to-uni connections, or hook snells consistently
• You're building a gift kit for a serious saltwater angler — this is a tool that gets used every trip

Best Fishing Techniques

• Leader building (fluorocarbon and monofilament)
• FG knot and uni-to-uni connections on braid-to-leader junctions
• Hook snells and Palomar knots
• Any application where you need a fully seated, tight knot on heavy line

Best For

• Offshore and nearshore saltwater anglers rigging with 30–100 lb leaders
• Anglers who tie their own rigs and leaders regularly
• Boat deckhands and guides who re-rig throughout the day
• Anyone who has ever cut their hand cinching a knot and decided not to do it again

Key Features

• Two-piece screw-together design — compact, fits in a pocket or tackle tray
• Black rubber coating on both pieces — grip surface for the line and your hand
• Hook slot — accept a hook directly for cinching connection knots at the hook end
• Keyring hole — attach to a lanyard or tackle bag zipper
• Available in 4" size (3" also available — contact us if you need it)
• Made by Accurate Reels

Tackle Express Tips

• Use both pieces of the knot puller simultaneously for FG knots — one on the braid tag end, one on the leader. You'll get a noticeably tighter, more consistent finish than pulling by hand or with gloves.
• Keep one clipped to your tackle bag zipper on a lanyard. It's the kind of tool you always know where it is until you don't bring it — then you miss it every rig.
• The rubber coating works better dry. If your hands are wet, give the puller a quick wipe before pulling down on heavy fluorocarbon so the line seats cleanly against the grip surface.

FAQ

What sizes does the Accurate Knot Puller come in?
Accurate makes the knot puller in a 3" and 4" version. The 4" is stocked here. If you need the 3" version, contact us and we can check availability.

Can I use this for braid-to-leader connections?
Yes — it works well for any line-to-line or line-to-hook connection where you need to apply pulling tension to seat the knot. The rubber-coated grip surface gives the line traction so you can pull fully without it cutting into your skin.

How do I attach it to my gear so I don't lose it?
There's a hole at the top of the knot puller designed for a keyring or lanyard. Most anglers clip it to a tackle bag, rod holder, or belt loop so it's accessible without digging through a tray mid-trip.

The Accurate Reel Clamp Kit is the OEM mounting hardware for Accurate reels — designed to lock your reel to the rod seat with zero movement under heavy drag and high-torque cranking. Available in standard and narrow versions across multiple finish colors to match your setup.

Loose Reels Lose Fish

A reel that shifts or creeps on the rod seat during a long fight isn't just annoying — it affects your leverage, changes your drag angle, and can compromise the rod-reel connection at the worst possible moment. Accurate's OEM clamp kits are the correct hardware for these reels, machined to fit the seat studs precisely. A proper clamp means the reel stays exactly where you set it, from the first crank to the last.

Wide Compatibility

These clamp kits fit the full range of Accurate conventional reels:

• Boss series
• Valiant series
• Extreme series
• Dauntless series
• Fury series
• Tern series

Important: Select the Narrow option for narrow-spool models including 400N, 500N, and 600NN. Standard and narrow clamps are not interchangeable — verify your reel model before ordering.

The Right Pick If...

• Your existing clamp is worn, damaged, or missing and you need OEM replacement hardware
• You're building a new rod-and-reel combo and need the correct clamp for your Accurate reel
• You want to color-match your clamp to your reel finish (silver, black, red, or gold)
• You're running a narrow-spool Accurate and need the correct narrow clamp — not a standard one

Key Features

• OEM Accurate hardware — correct fit for Boss, Valiant, Extreme, Dauntless, Fury, and Tern series
• Available in Standard and Narrow — narrow fits 400N, 500N, 600NN models
• Five finish options — Narrow Silver, Silver, Red, Black, Gold
• Complete kit — includes all hardware needed for installation
• Corrosion-resistant finish — built for saltwater environments

Models & Variants

Tackle Express Tips

• If you're unsure whether your reel is a standard or narrow spool, check the model number. Any model ending in N (e.g., 500N, 600NN) requires the Narrow clamp. Standard models without the N suffix take the regular clamp.
• Apply a small amount of anti-seize compound to the mounting studs before installation — it makes removal much easier after extended salt exposure and prevents the hardware from galling over time.
• Inspect the clamp hardware annually, especially on reels that see heavy drag pressure regularly. The studs and nuts are the weak point — if they show corrosion or wear, replace the kit before your next offshore trip.

FAQ

How do I know if I need the Narrow or Standard clamp?
If your reel model number includes an N (e.g., 400N, 500N, 600NN), you need the Narrow version. Standard models without an N suffix take the standard clamp. If you're still unsure, contact us with your reel model number and we'll confirm.

Does this kit include all the hardware I need?
Yes — the kit includes the clamp, mounting studs, and securing nuts. Everything needed for a complete installation is included.

Will this fit my Accurate Ascender?
The Ascender has its own dedicated clamp kit listed separately. These kits are for Boss, Valiant, Extreme, Dauntless, Fury, and Tern series reels. Check the Accurate Ascender Reel Clamp Kit listing if you have an Ascender.

Your Accurate reel is a serious investment. The Accurate Reel Cover is a custom-fit neoprene cover designed specifically for Accurate reels — not a generic slip-on, but a tailored cover that fits the profile of the reel correctly and stays put. Whether you're traveling to the grounds, storing rods in a rod locker, or hanging a rigged rod between drifts, this cover keeps your reel protected and your hook or lure secured.

What Generic Covers Get Wrong

A loose or ill-fitting cover bunches up, falls off, and doesn't protect the parts that matter — the drag knob, handle, and side plates. The Accurate cover is built to the dimensions of their own reel lineup, so it seats cleanly against the frame without gaps. The rear wrap secures around the back of the reel or rod so it won't work loose in a rod locker or during transport.

What's Included

• Neoprene construction — soft, form-fitting protection that won't scratch your reel or rod
• Heavy-duty composite ring — built into the cover for hooking lures or hooks when the rod is rigged and stored
• Rear wrap — wraps around the back of the reel or rod seat to secure the cover in place
• Accurate logo and signature red/black colorway — clean look that matches Accurate's reel aesthetic

Size Guide

The Right Pick If...

• You store rigged rods in a rod locker or rod rack and want the hook or lure contained
• You're traveling to a charter or overnight trip and want your reel protected during transport
• You want an OEM Accurate cover that actually fits your reel — not a generic neoprene bag
• You're gifting a reel or building out a complete rod-and-reel setup and want the finishing touch

Key Features

• Custom fit — designed specifically for Accurate reel dimensions
• Neoprene construction — soft, scratch-free protection
• Composite hook ring — secures your rigged hook or lure
• Rear wrap secures cover — won't fall off in a rod locker
• Accurate branding — red and black logo colorway
• 4 sizes — Small, Medium, Large, X-Large

Tackle Express Tips

• When in doubt between two sizes, go larger. A slightly loose cover is better than one that stresses the neoprene and doesn't seat cleanly over the handle and drag knob.
• Use the composite ring to clip the hook of a rigged jig or live bait rig to keep it from swinging and fouling other rods in the locker during a run to the grounds.
• Rinse the cover with fresh water after saltwater trips just like you would the reel. Salt buildup in the neoprene can transfer back to the reel's finish over time.

FAQ

Which size fits a Valiant 500N?
The Medium (ARC-M) fits the 500N. It also covers the 400, 400N, and standard 500.

Does this cover work on a rod-and-reel combo, or just the reel alone?
Both. The rear wrap is designed to go around the back of the reel or secure to the rod seat area, so it works whether the reel is mounted on a rod or stored off the rod.

Is this the same cover Accurate ships with their reels?
Yes — this is the OEM Accurate reel cover. It's the same cover included with many of their reels and sold separately as a replacement or additional cover for spare setups.

The AFTCO Alijo Fighting Day Belt is designed for use with 20-lb. to 50-lb.lines and is the perfect "day belt" for stand-up fishing against sailfish, dolphin, kingfish, small tuna, yellowtail and other smaller to medium-sized gamefish.  Stamped from pure marine grade gold anodized aluminum with a super-comfortable over-molded, closed cell polyurethane pad, the Alijo fishing belt accommodates the same "Quick Clip" nylon straps as the larger AFTCO fighting belts.  The stainless steel gimbal cross pin is removable, but unique is the thermal-formed nylon liner inside the aluminum gimbal pocket that helps resist scarring.  The Alijos fishing rod holder belt is lightweight and easy to wear, yet offers the same heavy-duty features of the larger AFTCO fishing rod holder belts.

• The premier day belt for use with 20-lb to 50-lb tackle.
• Thick, closed-cell EVA foam pad is molded on backside with vent slots and contours engineered for superior comfort.
• Stainless steel gimbal pin can be removed.
• Gimbal pocket lined with thermal-formed nylon to resist scarring.
• Double box-stitched ultra heavy-duty adjustable 2” nylon web straps.
• Lightweight stamped aluminum front plate deeply anodized in a rich gold finish for extreme durability and corrosion resistance.
• Adjustable one size fits most (28-50” waist).

The AFTCO Goldfinger Outrigger release clip should be attached directly to the outrigger halyard without the use of swivels. The adjustment-slider end of the clip needs to be "up" towards the tip of the outrigger. For fixed position bait trolling,the fishing line should be twisted 5 to 10 times before hooking loop over the clip's bail. The line may also be passed over the bail without twists to allow for adjustment of baits or lures.

1 Clip Per Pack

• Super lightweight design
• 12 Tension settings
• Oversized, polished, Gold Titanium-Nitride Coate

Keep Your Lines Down and Your Lures Working

When you're trolling from the stern, line angle is everything. The AFTCO Roller Troller Flat Line Clip puts your flat lines into the water at a lower, more productive angle — keeping lures below the surface where they run true, reducing tangles with other lines, and delivering instant, clean releases the moment a fish strikes. No hesitation, no missed hookups.

Engineered for Offshore Punishment

This isn't a clip you'll be replacing every season. The Roller Troller is built around a stainless steel roller with an AFLON™-treated bearing that handles the constant friction of trolling without wearing down. The 135-lb coated stainless steel cable and heavy-duty snap swivel are rated for the biggest fish you're likely to encounter. Micro-tension adjustment lets you dial in the release sensitivity for different lure weights and sea conditions.

Why Flat Line Angle Matters

Lines trolled at a steep angle create drag, reduce lure action, and are more likely to tangle with outrigger lines. A flat line clip solves all three problems — your lures run deeper, swim more naturally, and stay separated from the spread. When a fish hits, the clip snaps open instantly so you're fighting the fish, not the clip.

The Right Pick If...

• You're running a multi-line trolling spread and need clean line separation
• You want a release clip that won't prematurely pop or fail to release
• You're targeting big-game species that require a solid, reliable setup
• You need adjustable tension to match different lure weights and conditions

Best Fishing Techniques

• Flat line trolling from the stern with lures or rigged baits
• Multi-line spreads with outriggers — keeps flat lines separated and productive
• High-speed trolling for wahoo and tuna
• Slow trolling with rigged ballyhoo or mackerel for billfish

Best Conditions

• Offshore blue water trolling in any sea state
• Any situation where line angle and lure depth need to be controlled
• Multi-line spreads where tangle prevention is critical

Best For

• Species: Marlin, sailfish, wahoo, mahi-mahi, yellowfin tuna, bluefin tuna
• Techniques: Flat line trolling, multi-line spreads, high-speed trolling, slow-trolled rigged baits
• Use Cases: Stern flat line clips, trolling spread organization, release clip replacement

Key Features

• Stainless steel roller for smooth, low-friction line release
• AFLON™-treated bearing for long-lasting performance under constant use
• Micro-tension adjustment — dial in release sensitivity for any lure or condition
• 135-lb coated stainless steel cable — rated for serious offshore fish
• Heavy-duty snap swivel for quick attachment and reliable connection
• Instant snap-open release on strike — no hesitation, no missed fish
• Sold individually (1 clip per pack)

Models & Specs

Tackle Express Tips

• Start with lighter tension: When first setting up, dial the micro-tension to the lighter end and work up. A clip that's too tight can delay the release and cost you a fish.
• Position matters: Mount your flat line clip as close to the water as practical — the lower the angle, the better your lure action and the less chance of tangling with outrigger lines.
• Inspect the cable regularly: Even coated stainless can show wear after heavy use. Check the cable and snap swivel before each trip and replace if you see fraying or corrosion.

FAQ

How does the micro-tension adjustment work?
The tension adjustment controls how much force is needed to pop the clip open on a strike. Lighter tension is better for smaller lures or when targeting fish that hit softly; heavier tension works better for large lures or high-speed trolling where wave action might cause false releases.

Can I use this clip with both lures and rigged baits?
Yes. The adjustable tension makes it versatile for both high-speed lures and slower-trolled rigged baits like ballyhoo or mackerel. Just adjust the tension to match the lure weight and trolling speed.

Is this sold as a single clip or a pair?
The AFTCO Roller Troller Flat Line Clip is sold individually — 1 clip per pack. Order two if you're running flat lines on both sides of the stern.

Control Your Spread. Miss Fewer Fish.

The AFTCO Roller Troller Outrigger Clips give you something most outrigger clips can't: the ability to reel line directly through the clip without removing it. Position your lure exactly where you want it by simply reeling in or letting out line — the line rides on a silky-smooth AFLON™-treated roller that won't nick or weaken your leader. When a fish strikes, AFTCO's precision-engineered latching system releases at exactly the same pull every time, so you get consistent hookups and fewer broken rigs.

Precision That Pays Off on the Water

Inconsistent release tension is one of the most common causes of missed strikes and broken gear. The Roller Troller's improved micro-tension adjustment is positive and sensitive across a wide range of settings — once you dial it in, the latch releases at the same force on every strike. That repeatability means you can fine-tune your spread for different lure weights, trolling speeds, and target species without second-guessing your setup.

Why Outrigger Clip Quality Matters

A cheap clip that releases too early causes false drops and wasted time re-rigging. One that's too stiff delays the hookset and costs you fish. The Roller Troller sits in the sweet spot — adjustable enough to handle everything from light ballyhoo rigs to heavy lures, and reliable enough that you can trust it trip after trip. The AFLON™ bearing handles constant friction without wearing down, even in saltwater conditions.

The Right Pick If...

• You want to adjust lure position without removing the clip from the outrigger line
• You need consistent, repeatable release tension across your entire spread
• You're targeting big-game species where a missed strike is a missed opportunity
• You run kite fishing rigs and need a reliable, adjustable clip

Best Fishing Techniques

• Outrigger trolling with lures or rigged baits
• Kite fishing — compatible with kite line setups
• Multi-line trolling spreads requiring precise lure placement
• High-speed trolling for wahoo and tuna
• Slow trolling with rigged ballyhoo or mackerel for billfish and sailfish

Best Conditions

• Offshore blue water trolling in any sea state
• Any spread where lure depth and position need to be controlled precisely
• Multi-line setups where consistent release tension is critical

Best For

• Species: Marlin, sailfish, wahoo, mahi-mahi, yellowfin tuna, bluefin tuna
• Techniques: Outrigger trolling, kite fishing, multi-line spreads, high-speed and slow trolling
• Use Cases: Outrigger clip replacement, trolling spread setup, kite fishing rigs

Key Features

• Reel line directly through the clip — adjust lure position without removing from outrigger
• AFLON™-treated bearing for smooth, long-lasting roller action
• Improved micro-tension adjustment — positive and sensitive across a wide range
• Precision-engineered latching system releases at the same pull every time
• Reduces missed strikes and broken line from inconsistent release
• Sold as a 2-clip pack

Models & Specs

Tackle Express Tips

• Match tension to lure weight: Heavier lures need more tension to prevent false drops from wave action. Start light and increase until you stop getting premature releases.
• Use both clips symmetrically: Set both clips to the same tension so your port and starboard lines drop at the same time on a double strike — critical when targeting billfish.
• Rinse after every trip: The AFLON bearing is built to last, but a quick freshwater rinse after saltwater use keeps the roller spinning freely and extends the life of the clip.

FAQ

Can I adjust lure position without taking the clip off the outrigger line?
Yes — that's one of the Roller Troller's key advantages. Simply reel in or let out line and it feeds right through the clip on the roller. No need to drop the outrigger or re-rig.

Is this compatible with kite fishing setups?
Yes. The Roller Troller Outrigger Clip works well for kite fishing applications where adjustable, consistent release tension is important. The micro-tension adjustment lets you dial in the right setting for kite line conditions.

How is this different from the Flat Line Clip?
The Outrigger Clip is designed for use on outrigger and kite lines, where the line runs through the clip at an angle from above. The Flat Line Clip is designed for stern flat lines trolled at a lower angle. Both use the same AFLON roller and micro-tension system, but are configured for different positions in the spread.

Atlas Mike’s Magic Thread is the ultimate solution for securing bait quickly and easily—no knots needed! Whether you're wrapping roe bags, liver, shrimp, or soft baits, this elastic thread gives you a strong, secure hold with just a few wraps and a quick pull to tighten. Ideal for freshwater and saltwater anglers alike, Magic Thread keeps your bait in place longer so you can focus on fishing.

Key Features:

• No Knots Required – Simply wrap, pull, and it holds tight!

• Versatile Use – Perfect for securing roe, liver, shrimp, or soft baits.

• Strong & Stretchy – Durable elastic thread stretches and grips securely.

• Mess-Free Application – Keeps your hands clean while baiting.

• Available in Multiple Colors – Choose the color that best matches your bait presentation.

Perfect for salmon, steelhead, trout, catfish, and more, Atlas Mike’s Magic Thread is a must-have in every angler's tackle box. Fast, easy, and reliable—just wrap it up and fish on!

Quantity 1

Protect Your Avet Reels Between Trips

Avet Reel Bags are padded, soft-sided cases built to keep reels organized and protected during travel, storage, and transport to the boat. Heavy-duty black nylon, movable padded dividers, multiple zippered pockets, and a removable shoulder strap turn a pile of reels and accessories into a setup you can carry with confidence.

Open the bag at the dock and everything has a place: reels in padded compartments, leaders and tools in the zippered pockets, and the shoulder strap ready when you need both hands free. The front carries a color-embroidered Avet marlin logo, and both sizes are designed around practical reel storage rather than wasted space.

Stop Letting Reels and Accessories Travel Loose

Unprotected reels can knock against each other, while leaders, manuals, and small tools disappear into separate boxes. The Avet Reel Bag solves that everyday organization problem with adjustable compartments and dedicated pocket space, so your gear stays together from the truck to the rail.

Built for Travel, Storage, and Quick Organization

• Padded nylon construction: Adds a protective layer around reels during transport and storage.
• Movable padded dividers: Hook-and-loop dividers let you configure the main cargo area around your reel setup.
• Multiple zippered pockets: Keep leaders, tools, manuals, and accessories organized.
• Adjustable shoulder strap: Wide, comfortable, removable, and fitted with quick-release buckles.
• Heavy-duty black nylon: Made for regular travel to and from saltwater trips.
• Avet marlin logo: Color-embroidered on the front.

The Right Size If...

• Choose Small when you need a compact case for up to six reels and six pockets.
• Choose Large when you need more room for up to ten reels, ten pockets, and the listed zippered expansion seam.
• You want one organized case instead of loose reel boxes, leaders, and accessories.
• You regularly travel to the boat, long-range landing, tackle room, or storage locker.

Best For

• Transporting Avet saltwater reels between home, vehicle, and boat.
• Storing reel pairs and accessories between fishing trips.
• Organizing leaders, tools, manuals, and small tackle-room essentials.
• Keeping a reel collection together for offshore and long-range fishing.

Where It Fits in the Avet Setup

The Avet Reel Bag protects the reels you already own. Pair it with the Avet Reel Clamp Kits when you need replacement or color-matched clamp hardware. For a complete reel comparison before choosing what to pack, browse the Avet Reels Buyer’s Guide, then compare an offshore setup such as the Avet HXW Raptor 2-Speed Reel or the more compact Avet SX Raptor.

Key Features

• Padded soft-sided reel case.
• Heavy-duty black nylon exterior.
• Movable padded hook-and-loop dividers.
• Multiple roomy zippered pockets.
• Wide adjustable shoulder strap with quick-release buckles.
• Removable shoulder strap included.
• Color-embroidered Avet marlin logo.
• Small and Large sizes.

Size Guide

Available models and SKUs

Tackle Express Tips

• Measure your reel collection and compare it with the listed dimensions before ordering, especially for the Large case.
• Use the movable dividers to keep reels separated and stable instead of stacking them together.
• Place leaders and frequently used tools in the zippered pockets so the main reel compartments stay uncluttered.

FAQ

What is the difference between the Small and Large Avet Reel Bag?
The Small measures 14 in. × 9 in. × 8 in. and holds up to six reels with six pockets. The Large measures 22 in. × 14 in. × 12 in. and holds up to ten reels with ten pockets and a zippered expansion seam.

Are the dividers removable?
Yes. The padded dividers attach with hook-and-loop fasteners, so you can configure the compartments for your reel setup.

Is the shoulder strap included?
Yes. The wide adjustable shoulder strap is included, has quick-release buckles, and can be removed.

Shipping Note

Please review the dimensions carefully before ordering. Free returns are not available on this product, and oversize shipping charges may apply at checkout.

Secure Your Avet Reel to the Rod

Avet Reel Clamp Kits add a solid, corrosion-resistant connection between a compatible conventional reel and rod. The hardware is precision-machined from 6061-T6 aircraft-grade billet aluminum, then anodized for saltwater durability and a clean color-matched finish.

Choose the correct kit type and reel-size group before ordering. The current variants are labeled for SX/MXJ/MXL, JX/LX/HX, or EX models. The listed compatibility options do not include SXJ, HXJ, or HXW, so confirm fitment before placing an order for those reel families.

Keep the Reel Stable When the Fight Gets Heavy

A deckhand rod or conventional setup may not give your reel the support you need on its own. A properly matched clamp helps keep the reel seated and reduces unwanted movement while you troll, fish bait, work a jig, or lean into a hard-pulling saltwater fish.

Choose the Hardware That Matches Your Reel

• Screw Set: Replacement screws only for the SX, MXJ, and MXL compatibility group.
• Stud and Nut Set: Replacement studs and nuts for the JX, LX, and HX compatibility group.
• EX Stud and Nut Set: Replacement studs and nuts for EX-series reels.
• Colored Clamp Kit: A full anodized clamp with hook/jig holder. Screws and tools are not included.
• Color options: Multiple anodized finishes are listed across the compatible reel-size groups.

The Right Pick If...

• You need replacement clamp hardware for a compatible Avet reel.
• You fish a deckhand rod or conventional rod setup without a reel seat.
• You want a full clamp rather than a replacement screw or stud-and-nut set.
• You want to match the clamp finish to a Silver, Gunmetal, Red, Blue, Purple, Green, Gold, or Black reel setup where listed.
• You have checked the variant title against your exact Avet reel family before ordering.

Best For

• Offshore trolling and stand-up big-game fishing.
• Saltwater bottom fishing and heavy conventional tackle.
• Replacing lost screws, worn studs, or missing nuts.
• Adding a color-matched clamp and hook/jig holder to a compatible Avet reel.
• Organizing and maintaining Avet reels between trips.

Where It Fits in the Avet Setup

Pair the correct clamp or hardware set with the Avet Reel Bags to keep your reels and accessories organized between trips. For a reel-by-reel fitment starting point, compare the Avet SX Raptor, Avet LX Raptor, or Avet HX Raptor. The Avet Reels Buyer’s Guide can help you identify the reel family before you select hardware.

Key Features

• Precision-machined 6061-T6 aircraft-grade billet aluminum.
• Anodized finish for corrosion resistance and color options.
• Full clamp kits include a hook/jig holder.
• Replacement screw sets and stud-and-nut sets are available separately.
• Multiple fitment groups are clearly labeled by reel family.
• Compatible color groups include Silver, Gunmetal, Red, Blue, Purple, Green, Gold, and Black where listed.
• Designed for Avet conventional reel setups.

Kit Selection Guide

Models & Specs

Tackle Express Tips

• Match the exact reel-family wording in the variant title before adding a clamp or replacement hardware.
• Add a small amount of grease to the threads so the hardware seats securely and is easier to remove later.
• Keep spare screws or studs with the reel in your Avet Reel Bag so a small hardware problem does not end the trip.

FAQ

Do these clamp kits fit SXJ, HXJ, or HXW reels?
The current variants are labeled for SX/MXJ/MXL, JX/LX/HX, or EX groups. SXJ, HXJ, and HXW are not listed in the current compatibility options, so please confirm fitment before ordering.

What is included with the colored clamp kit?
The colored option is a full clamp with a hook/jig holder. Screws and tools are not included.

Which kit should I choose if I only lost the screws?
Choose the Screw Set for the SX/MXJ/MXL group, or the appropriate Stud and Nut Set for the JX/LX/HX or EX group.

Complete the Setup

Store the reel and spare hardware together in the Avet Reel Bags. Before ordering, use the Avet Reels Buyer’s Guide to identify your reel family, then compare the Avet HX Raptor or Avet SX Raptor listings for model context.

Avet Reel Cover is a form-fitting neoprene case that protects your reel while it is mounted on the rod or stored between trips. The hook-and-loop handle band keeps the cover secure, while the top ring gives you a handy place to clip a lure or hook without removing the reel.

Keep Your Reel Protected Between Trips

Salt spray, deck scuffs, and tackle-room clutter can make a good reel look rough fast. This soft neoprene cover adds a practical layer of protection without the bulk of a hard case, and five size options make it easy to match the cover to compact baitcasters, Avet SX reels, or larger offshore models.

Why This Cover Earns a Spot in the Tackle Bag

• Form-fitting neoprene: Cushions the reel and helps protect the finish during transport and storage.
• Hook-and-loop handle band: Wraps around the handle to help keep the cover in place.
• Top lure ring: Clip a lure or hook while the reel stays on the rod.
• Five size choices: Covers the Avet range from SX through EX50 and EXW50.
• Broad compatibility: The Small size also fits many low-profile baitcasters, including Daiwa 300 and Shimano Curado models.

Choose the Right Size

Match the cover to the reel family below. If your reel is between sizes or from another brand, compare its overall profile with the fit guide before ordering.

Fitment Details

The Right Pick If...

You want lightweight protection for an Avet reel that travels between the boat, truck, and tackle room. Choose Small for an Avet SX or a compatible low-profile baitcaster, Medium for MXJ and MXL, Large for JX through HXW, X Large for EX30, and XX Large for EX50 or EXW50.

Tackle Express Tips

• Measure or compare your reel profile before ordering if you are using a brand or model outside the listed Avet fit guide.
• Let the cover dry fully after a saltwater trip before storing the reel for an extended period.
• For a more secure rod setup, pair the cover with the Avet Reel Clamp Kit and keep the reel protected during transport.

Complete the Avet Setup

Protect a compact reel with the Avet G2 SX Series Reel, compare a medium-size option with the Avet G2 MXJ Single Speed Reel, or see the Avet JX Raptor 2-Speed Reel for a larger platform. Read the Avet Reels Buyer's Guide for help comparing reel families and applications.

Frequently Asked Questions

Which size fits an Avet SX reel?
The Small cover is listed for all Avet SX reels.

Can I use this cover on another reel brand?
Yes. It is custom-made for Avet reels but also fits many other brands. The Small size is specifically noted as a fit for low-profile baitcasters such as Daiwa 300 and Shimano Curado models.

Does the cover stay on while the reel is mounted?
Yes. The hook-and-loop band wraps around the handle to help secure the cover, and the top ring lets you clip a lure or hook while the reel remains on the rod.

Easily measure your catches with the compact and lightweight Battlestar 28" Fish Measure Tape. With a slim 3" width and minimal memory, it unrolls and lays flat, taking up minimal space in your surf pack. Get ready to qualify a legal White Sea Bass with ease.

• 3" wide
• 0.93oz
• Measures to 28"

Keep your favorite bottled or canned beverage cold with these neoprene coolers. Features the original one color Calcutta logo and solid bottom.

Calcutta Can Cooler Features:

• 3mm Neoprene
• Solid Round Bottom
• One color Original Calcutta Logo

The Cork Puppy Reel Clamp is designed for west coast jig fishermen and long-cast anglers using deckhand-style rods with no reel seat. These rods require a rod clamp to mount the reel, and the Cork Puppy solves that problem cleanly — locking the reel in place without twisting, turning, or crushing the blank, in a low-profile design that keeps the setup comfortable and balanced for longer casts.

Machined from 6061-T6 aluminum with type II anodizing. Available in three sizes measured by the rod's diameter at the intended mount point.

Key Features

• Locks reel in place — won't twist or turn
• Won't crush the blank
• Low profile — comfortable, balanced feel
• Machined 6061-T6 aluminum with type II anodizing
• 3 sizes: 25mm, 28mm, 31mm
• Color: Black only

Size Guide

Measure the rod's diameter at the point where you intend to mount the reel. To convert inches to mm, multiply by 25.4. If you don't have calipers, wrap a piece of string around the rod at the mount point, mark where it meets, measure the length, and divide by 3.14 to get the diameter.

Costa Hermit Cloth Wipe makes  always having a lens cloth handy. keep one in your car, another in the boat, RV, backpack, purse, etc.  The soft plastic case has the cloth attached inside so you can't loose it.  This keeps the cloth from getting dirty so when you clean your glasses you won't scratch them or smear.  The clip allows you to attach it to waders or anywhere you may need it within easy reach.  Try one out, we love them at Tackle Express and we think you will too.

FEATURES

• Branded Silicone Casing
• Attached Clasp
• Solid Microfiber Cleaning Cloth

Description:

The Costa Megapren Retainer slides onto frame arms and grip tight. The wide design makes them comfortable when glasses are on, or hanging around your neck.

FEATURES

• 3mm Thick Neoprene Retainer
• 1.25” wide x 17” long
• Sublimated Graphic with Costa Logo and Wordmark
• Embroidered Costa Logo

Description:

Costa Recycled Microfiber Pouch.

FEATURES

• Regular Fit
• Men's Cut
• Taped neck and shoulder seams
• Printed Design
• 100% Preshrunk Cotton. 6 OZ
• Machine wash cold, inside out, with like colors. Tumble dry low. Iron inside out on low setting. Do not use bleach. Do not dry clean.

Details:

Color: 

Costa Blue

Item No: 

KC 01PK

Description:

• Costa Clarity Kit
• Micro-Fiber Cleaning Cloth
• Anti-reflective lens cleaner for glass or plastic lenses
• Durable carrying case